Tel: 008618201460928

WhatsApp : 008615200089972

Zip code:102600

Address: XingHua Street DaXing Beijing China

Tel: +86-10-60350373

Home / Diode laser 808

Diode Laser

2017-11-05 17:34:26


Product Description


Technical Specification



Treatment principle is based on the role of selective photothermolysis, as hair follicle and hair shaft are rich in melanin, melanin in the hair bulb matrix distribution between cells and transfer to the structure of hair shaft, the regard melanin as target to do hair removal treatment, after the target and its carrier ( hair follicle and hair follicles surrounding tissues) absorb the tremendous energy, the temperature increased sharply, leading to hair follicle tissues and surrounding hair follicle tissues damage, hair loss the native environment, it must be completely removed.

Energy Fluence 0~120J/cm2
Wavelength 808nm/755nm/1064nm
Pulse Width 0ms~600ms
Repetition Rate 1Hz~10Hz
Skin Cooling temperature -5--5℃ by cooled Sapphire 
Spot size 11x11mm or 10x17mm optional
Interface language English or other 8 kinds language optional
LCD Screen 10.4’
System Cooling method Freon compressor
Input VAC 220VAC / 50-60Hz
Product  Installatation

Do not power up the system before you checked this manual!
1. Please check all the part in packing list to confirm all the part are received.
2. Add water to water tank. Please confirm your machine model. OL-DHR-MI means the there are micro channel cooler laser stack in the handle piece. It need DI-water. Otherwise laser handle piece are easily broken. Connect the water tube to the water inlet and water spilt hole. Make sure water inlet and water spilt are connected with CPC connector at same time. Use funnel to add water till water spilt from the overflow hole. You may need ~1.5 liters of water.
3. Connect the handle piece to main machine. Check the handle piece if it is in good conditions. Make sure the water tube is well connected. You will hear “kink” when the water connector are well locked. Otherwise, there will be water leakage or water jam which may cause water pump broken or laser burning out.
1) Please confirm if your wall-plug is 200-240VAC. If it is 90-120VAC, please use voltage transformer.
2) Find a 10A 220-250V VAC plug wire (you may need an European Model for the wire), connect to the back panel.
3) Check if the emergency button is pressed down. If pressed down, please release it.
Use the key to start the system and you will enter the welcome interface of the system as below:


1) Press the welcome bottom, you will enter the second page as the right picture above. Till now, you are successfully enter the hair removal system. Please follow the “6. OPERATION” chapter to start the treatment.
2) For any emergency situation, please press the emergency button (Red Mushroom) to shut down the laser immediately.
3) After treatment if you want to turn off the system, you can use the key to shut it down directly. And turn off the air switch at the back panel. You can remove the VAC plug if necessary.

HR-Hair removal
It is a professional model. In this model, you first choose patient skin color, sexual and treatment body part in Body Page(left picture above). Press “OK” to enter next page. Or press “reset” to rechoose.
Our smart system will give you recommended parameter of laser power, pulse width and frequency depending on your choice of sexual, skin color type and treatment body part. Those default will display in the corresponding column. If you want to follow those default, just press “OK”. If want to adjust your favourite parameter, press”SET”, then you can adjust laser power and frequency by “+” and “-”. Bottom “use recommended parameter” will reset those three parameter to default.
There are totally 3 parameters to be set, including: Laser Power, Frequency and Skin Cooling Level.
1) The Fluence shows the energy density of one laser shot. Laser Power fluence can be variable from 1J~120J. The step width is 1J. You can adjust it by press “+” and “-”.
2) The Frequency shows the pulses per second of the laser. A higher repetition rate leads to higher pulse energy fluence. The frequency can be variable from 1Hz~10Hz with a step width of 1Hz.
3) Subtotal at the top-right of the LCD screen shows the total laser energy of this treatment. It is easy for doctor to calculate how much power used in one treatment. Press button “clear” can clear the number. Or the subtotal number will clear automatically when machine shut down.
4) The Skin Cooling Level shows cooling efficiency of the Sapphire Window and Aluminum Tip of the handle piece. The green block is longer, the cooling is better. It depends on the feeling of the patents. The default cooling level is minimum output, which can be adjust by pressing “+” and “-” button. When the laser is working, you can not adjust skin cooling level. You may need to wait for several minutes before the skin cooling tip becomes cold.
5) The column below skin cooling shows the system status.
A. Status: Setting. This means you are setting parameters.
B. Status: Ready. When parameters have been set, press “READY” button, the system will enter ‘Ready’ status. In this status, the laser is ready to use.
C. Status: Working. When the handle piece shots laser pulses, the system will enter to ‘Working’ status.
D. Status: Water temperature high. The cooling water temperature range should be between 15~28℃. If it higher than 30℃, the laser will stop. Please wait till water temperature going down. The warning will disappear, and system can be set again.
E. Status: Water flow rate low. It means the cooling water flow rate lower than minimum requirement. If the water flow rate which show at the bottom of the screen is just low, not “0 L/min”. Please first check along the water tube to confirm whether there are any jam in it and handle piece water connector are well locked. Secondly, open the water inlet at the back of machine to make the air pressure balance between the inside and outside of water circle system. If the water flow rate show “0 L/min”. Please first check whether the water pump are working. Or contact our company to ask for help.
F. Status: Filter and deionized water need to be changed. It means the conductivity of cooling water is higher than 20us/cm. Just wait for a minute till to water cleaned by filter in side the machine. The conductivity parameter on the interface 3 will be obviously come down. Then warning will disappeared. If the conductivity don’t go down for long time, please ask professional technician to change the ion exchange filter inside the machine.

A. Status: Operation wrong. Press switch on the handle piece without enter ready status.
B. Status: Please check Diode laser or diode driver. It means the laser handle piece or laser power supply broken. Please ask factory or seller to solve this problem.
C. Status: Error 2. It means the control board have cooling problem. Please ask factory or seller to solve this problem.
1) Set the parameters (Fluence, Frequency, Cooling) and press ‘READY’ button to enable the handle piece. For the typical treatment parameters, you can refer to the recommended default or experienced doctor’s advice.
2) During ‘Ready’ status, you also can adjust the skin cooling depending on skin feeling. You may need to wait for several minutes before the skin cooling tip becomes cold.
3) Take the handle piece. Pressure the pedal switch or the switch on the handle piece to shot the laser pulses. Keep pressing the button and the laser output will continue. Do not press & release for single pulse.
4) You can stop the machine anytime by turn off the key in the front panel or press emergency button.

FHR-Fast Hair Removal

You can choose FHR button to enter the fast hair removal mode. There are five units parameters which are used frequently. Just choose one of then and adjust skin cooling level. You can start treatment directly.
SR-Skin Rejuvenation




808nm diode laser is also good for skin rejuvenation. Our system offer “soft”, “comfortable” and” effective” modes to match customer needs. Adjust skin cooling to let customer feel well.
Please follow those parameter during operating the machine:

Model No. OL-DHR-MI
Laser Cooling Liquid DI-water
Water Tank Volume ~1.5L
Handle Piece Flow Rate 2.5L/min+-10%
Cooling water temperature 23~28℃
Working Environment Temperature 15~28℃
Environment Moisture <70%
Product Effect


Product  Advantage

1 . Professional 808 Diode Laser, suitable for hair with any colors
2 . Suitable for any kinds of skin
3 .Safe and Fast. It needs 3-4 treatments, the interval of each treatment are 3 weeks.
4 . No harm, no side effect.
5 .High Energy Density Output: Make sure good effective for any coloring matter -- 120J/cm2
6 .High frequency output–Make sure heating hair follicle, lasting hair removal, fast hair removal-----10HZ
7 . Big Spot Size: Fast and Effective Results------------------10*17mm / 11*11mm
8 . Strong Cooling: Instance cooling skin ,safe & comfortable---- 5 degree.

Our services

1.We have 2 years warranty, and lifetime maintenance.
2.Within one month, if the machine is of any big fails, we will send you a new machine.
3.Within 2 year, we will be responsible for the repair if equipment is with small problem,we can delivery the part to you,you fix it according to our install instructions.
4. After 2 years, we also repair the machine, but you need to pay the cost of the changed parts.
5. For your consultation, we offer on-line service.